Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
After
Before
AfterHow Much Does Custom Window & Door Order Cost in Davie?
Custom window and door orders in Davie, FL typically run between $850 and $6,200 per opening, depending on size, glass type, frame material, and impact rating. Most Davie homeowners ordering a standard custom impact window land between $1,100 and $2,800 installed, while custom entry doors and oversized sliders push toward the higher end of that range. At Sightline Windows & Doors, the written price you receive after the measured survey is the same document that governs the install – no revision, no surprise line items at the end.
Custom Window & Door Order Cost Breakdown (2026)
The table below reflects installed pricing in the Davie market as of 2026. “Installed” means the unit arrives, the old frame is removed (where applicable), the new unit is set and sealed, and the job is photographed before we leave. Hardware, permits where required by Broward County, and the written measured survey are included in Sightline’s scope – not itemized as add-ons after the fact.
| Product Type | Typical Size / Spec | Installed Price Range (Davie, 2026) |
|---|---|---|
| Custom Impact Single-Hung Window | 24″x36″ to 36″x60″, PGT or CGI | $850 – $1,600 |
| Custom Impact Double-Hung Window | 28″x48″ to 36″x60″, ES Windows or CWS | $1,100 – $2,100 |
| Custom Impact Picture / Fixed Window | Up to 48″x72″, ECO Window Systems or PGT | $950 – $2,400 |
| Custom Geometric / Specialty Shape Window | Arch, trapezoid, circle – any size | $1,400 – $3,800 |
| Custom Impact Sliding Glass Door | 6′ to 12′ wide, CGI or PGT | $2,200 – $5,400 |
| Custom Impact Entry Door (single) | Therma-Tru or ViewLux, standard to oversized | $1,800 – $4,200 |
| Custom Impact Entry Door (double / French) | Therma-Tru or Mr-Glass, with sidelites | $3,200 – $6,200 |
| Custom Impact Casement Window | CWS or ECO Window Systems, up to 36″x60″ | $1,200 – $2,600 |
A few things determine where your project lands in that range. Frame material is the first lever: aluminum frames – the most common choice in Davie because they hold up against the humidity off the Everglades and the salt-laden air that works its way inland from the coast – cost less per unit than vinyl or fiberglass but require a slightly heavier laminated glass unit to hit Miami-Dade Notice of Acceptance (NOA) specs. Glass package is the second lever: a basic laminated impact lite carries a lower unit price than a low-e, argon-filled unit with a SHGC (solar heat gain coefficient) below 0.25, which is what most Davie homeowners request when they’re replacing single-pane builder windows and want a measurable drop in their FPL bill. Third, rough opening condition matters. Homes in Davie built before 1995 – particularly the ranch-style blocks around Stirling Road and the older sections near University Drive – often have wood buck framing that has absorbed enough moisture to require remediation before a new unit can be set plumb. When we find that in the measured survey, we put the remediation cost on the same document. You see it before we touch a thing.
The measured survey itself is the document Sightline was built around. Sonia Raman set up the company’s quoting process so that the field measurement and the written price are one document – Haven Clause 1 of the Haven Standard. You keep a copy. That copy does not change between survey day and installation day.
What Affects Custom Window & Door Order Pricing in Davie
- Impact rating and NOA compliance: Broward County enforces Miami-Dade protocol for openings in the High-Velocity Hurricane Zone, which covers all of Davie. Every unit we order carries a Miami-Dade or Florida Building Code NOA. The laminated glass required for that rating adds $80-$220 per opening compared to a non-impact unit – but in Davie, a non-impact unit isn’t a legal option for most permitted work, so the comparison is mostly academic.
- Custom sizing versus catalog sizing: When a Davie home’s rough opening doesn’t match a manufacturer’s standard size – common in older neighborhoods like Harmony Ranches or the estate lots along Griffin Road – the unit goes to custom fabrication. Fabrication lead times for PGT and CGI custom orders currently run four to eight weeks from approval. A catalog unit ships in one to three weeks. The price difference per opening ranges from $150 to $600 depending on how far the dimension departs from the standard grid.
- Frame material and finish: Anodized aluminum (clear or bronze) is the baseline. Powder-coat colors – increasingly popular in Davie’s newer construction near Nova Southeastern’s campus – add $90-$180 per unit. Fiberglass frames from Therma-Tru cost more upfront but carry a lower U-factor, which matters if the room faces west and catches afternoon sun.
- Glass package and energy performance: A standard impact laminate meets code. A low-e coating with argon fill and a SHGC at or below 0.25 qualifies the unit for Florida’s energy credit program and typically cuts cooling load in west-facing Davie rooms by a measurable margin. That upgrade runs $60-$150 per unit above the base glass price.
- Opening condition and prep work: Stucco removal, wood buck replacement, and waterproof membrane repairs are the three items that most frequently add cost to a Davie job. We find them during the measured survey, price them on the same document, and don’t invoice anything that wasn’t on that document. In practice, about 30% of Davie jobs in pre-2000 homes require some level of opening prep.
- Permit and inspection fees: Broward County permit fees for window and door work are calculated on project value. A typical Davie permit for a five-window order runs $180-$380. We pull and manage the permit; the fee is listed as its own line on the written price, never buried in markup.
- Number of openings ordered together: Ordering six or more units in a single purchase allows us to consolidate the factory run, reducing per-unit fabrication cost. For Davie homeowners doing a whole-house custom order – a recurring project type in the planned communities around Arrowhead Golf Club – this can bring the per-opening price down $100-$250 relative to ordering the same units one at a time.
Before
AfterWhat a Custom Order Includes at Sightline
This section exists because “custom order” means different things at different companies, and the gap between what’s quoted and what’s delivered is where most disputes start. Here is exactly what a Sightline custom window or door order includes in Davie.
The Measured Survey
A Sightline technician – background-checked, uniformed, and identified by license number before arrival, per Haven Clause 3 – measures every rough opening you’re replacing. Those measurements go into the written price document you receive that day. The factory order is cut from those exact measurements. We don’t round. We don’t assume. If the opening is 33-7/8″ wide, the order reads 33-7/8″.
Factory Order Management
We manage the order through whichever of our eight manufacturer lines the spec calls for. If the opening requires a Miami-Dade NOA impact unit in a non-standard width, that goes to PGT or CGI. If it’s a fiberglass entry door with a specific panel profile and hardware prep, that goes to Therma-Tru or ViewLux. You don’t chase the factory. We do, and we give you a documented timeline at the time of order.
Installation
Units are set by the same crew that did the survey wherever possible. Old units are removed and disposed of. The new unit is set level, plumb, and square, then sealed with a backer rod and sealant system appropriate for Davie’s rainfall exposure. Stucco is patched at the perimeter. Interior trim is re-set. The opening is left cleaner than we found it.
Documentation
Every completed opening gets a photo record – before and after – logged to your job file under Haven Clause 4 (Evidence on Every Job). That record is yours. If a question arises six months later about how the sill was sealed or how the frame was anchored, the photos answer it. This is not an upsell. It’s standard.
365-Day Done Right Promise
If any defect in workmanship appears within 365 days of installation, we return and correct it. Written into the Haven Standard. Not a verbal assurance, not a courtesy policy – a documented obligation that comes with every Sightline job in Davie.
Davie-Specific Factors That Shape Custom Orders
Davie sits in western Broward County at an elevation that leaves it exposed to sustained wind loads from both Atlantic-track hurricanes and the storm systems that build over the Everglades to the west. That geographic position is why Miami-Dade and Broward require High-Velocity Hurricane Zone (HVHZ) compliance for all permitted window and door work here – a standard that eliminates a large portion of the product catalog available in other Florida markets.
In practical terms, this means every custom unit we order for a Davie address carries a current Florida Product Approval number and, for most applications, a Miami-Dade NOA. PGT’s WinGuard line, CGI’s Guardian Series, and ECO Window Systems’ impact aluminum product all carry valid HVHZ approvals. CWS carries approval on several frame profiles. We specify by opening, not by inventory.
Davie’s older residential stock also creates specific ordering challenges. The neighborhood blocks east of Flamingo Road and the areas around Pine Island Ridge include substantial 1970s and 1980s construction where original windows were set in wood bucks with no bond beam anchorage. Replacing those openings to current code requires concrete anchor screws set at defined intervals into the masonry – a detail that gets confirmed during the measured survey and documented in the written price before any order is placed.
The Town of Davie issues its own building permits, distinct from unincorporated Broward County. Permit timelines for custom window and door orders in Davie currently run approximately two to four weeks from submission. We submit the permit package concurrent with the factory order so that both arrive close to the same date, minimizing the gap between unit delivery and installation day.
How to Save on Custom Window & Door Orders in Davie
There are real ways to reduce per-opening cost on a custom order. There are also approaches that look like savings on paper but cost more over the life of the unit. Here’s the practical version.
Order More Openings at Once
Factory runs for custom sizes are priced partly by setup cost, which is amortized across the number of units in the order. A Davie homeowner ordering ten custom windows in a single purchase absorbs that setup cost across ten units instead of two. The savings are real – typically $100-$250 per opening – and the installation mobilization cost is also split across a larger scope.
Choose the Right Glass Package, Not the Most Expensive One
Low-e argon is worth the premium for west-facing Davie rooms that absorb afternoon sun from June through October. For a north-facing bedroom window, the payback period on the premium glass extends considerably. During the measured survey, we note the exposure and give you the straightforward trade-off in writing. We don’t upsell glass you won’t benefit from.
Don’t Over-Specify the Frame
Fiberglass frames carry better U-factors than aluminum, which matters in a room with significant glazing area. For a bathroom window or a small fixed lite above a door, the performance delta over aluminum is negligible and the cost difference is not. Specify fiberglass where it earns its price. Use aluminum where it doesn’t need to.
Use the Free Second Opinion Before You Sign Anything
If you have a written estimate from another company, bring it to us. Sightline’s Free Second Opinion on Any Written Estimate means we’ll review the scope, the spec, and the per-opening pricing at no charge. In Davie, we regularly see quotes where the glass package is under-specified for HVHZ compliance, which means the customer pays less upfront and more later when the permit fails inspection. We catch that in the review.
Understand What the Permit Covers
Some Davie contractors quote work without a permit to show a lower number. A permitted custom window or door installation in Davie is inspected by a Town of Davie building official who verifies anchor pattern, sealant, and NOA compliance. That inspection is the warranty your home insurance carrier will want to see if you ever file a wind claim. The permit fee is real money; skipping it is a larger risk. We pull permits on every job where one is required, and we list the fee as a separate line so you can see exactly what it costs.
For a free, written estimate on a custom window or door order in Davie, call (754) 254-8492. A live person answers, and the measured survey can usually be scheduled within a few days. Alternatively, visit our Custom Window & Door Order in Davie service page to see the full scope of what we order and install.
Key Takeaways
- Custom window and door orders in Davie run $850-$6,200 per opening installed, with most single-window orders landing between $1,100 and $2,800.
- Every unit ordered for a Davie address must carry HVHZ approval under Florida Building Code – this is a code requirement, not an optional upgrade.
- Older homes near Stirling Road, University Drive, and Flamingo Road frequently require opening prep work; Sightline prices that on the measured survey document, not as a change order.
- The written price you receive after the measured survey is the same document that governs the installation – Haven Clause 1 means the quote and the invoice are the same document.
- Ordering six or more units at once typically reduces per-opening cost by $100-$250.
- Sightline’s 365-Day Done Right Promise covers every installation in Davie for a full year after completion, in writing.
- Every completed job leaves a documented photo record – standard on every Sightline job, not an upsell.
FAQs – Custom Window & Door Order Cost in Davie
How much does a custom impact window cost installed in Davie, FL?
A custom impact window in Davie costs between $850 and $2,600 installed, depending on size, frame material, and glass package. A standard 36″x48″ single-hung aluminum impact unit from PGT or CGI in a pre-measured rough opening typically lands between $1,100 and $1,700. Specialty shapes – arches, trapezoids, and geometric units common in Davie’s newer communities near Arrowhead Golf Club – run $1,400 to $3,800 because they require custom factory fabrication and longer lead times. Call (754) 254-8492 for a written price tied to your specific opening measurements.
How long does a custom window or door order take in Davie?
From signed order to installation day, most custom window orders in Davie take five to nine weeks. Standard sizes within the manufacturer’s catalog run four to six weeks. True custom fabrication – non-standard dimensions, geometric shapes, or specialty glass packages – runs six to ten weeks. The Town of Davie permit, which we submit at the same time as the factory order, typically takes two to four weeks to return, so both arrive close together. You receive a documented timeline at the time of order, not an estimate given verbally and revised later.
Does a custom window or door order in Davie require a permit?
Yes. The Town of Davie requires a building permit for any window or door replacement, custom or otherwise. The permit is pulled by the contractor, not the homeowner, and a Town of Davie inspector verifies HVHZ compliance – anchor pattern, NOA approval, and sealant application – before the job is closed. At Sightline, the permit fee is a separate line on the written price document. It is not buried in markup. Skipping the permit creates a gap in your home’s wind-loss coverage that can affect insurance claims after a storm.
Is it cheaper to order custom or use a stock window size in Davie?
Stock sizes that fall within a manufacturer’s standard grid cost $150-$600 less per opening than true custom fabrication, and they ship faster. The honest answer for many Davie homeowners is that the rough opening can be furred or slightly adjusted to accept a catalog size, and that adjustment often costs less than the custom fabrication premium. During the measured survey, we flag that option in writing if it applies. We don’t push custom orders when a standard unit fits the opening and the code requirements equally well. The goal is the right unit for the opening, priced accurately on the document you keep.
What manufacturers does Sightline use for custom window and door orders in Davie?
Sightline draws from eight manufacturer lines: PGT, CGI, CWS, ES Windows, ECO Window Systems, Mr-Glass, Therma-Tru, and ViewLux. The line selected for a given opening depends on the performance spec the opening requires – HVHZ approval status, U-factor, SHGC target, frame profile – not on what’s in stock or what carries the highest margin. For most Davie impact window orders, we specify PGT WinGuard, CGI Guardian, or ECO Window Systems aluminum. Entry doors with custom panel profiles typically go to Therma-Tru or ViewLux. We document the specified manufacturer and product series on the written price; you see exactly what you’re getting before we place the order.
Can Sightline match a competitor’s custom window quote in Davie?
Bring us any written estimate from a competitor and we’ll review it at no charge – product spec, scope, and per-opening pricing. If the spec is equivalent and our price is higher, we’ll tell you. More often, the review surfaces a difference in spec: a glass package that doesn’t meet HVHZ requirements, anchor spacing that won’t pass inspection, or a unit without a current Florida Product Approval number. Those differences matter because they affect the permit inspection and, eventually, your insurance coverage. The review is free. Call (754) 254-8492 to set one up.
Why Sightline for Custom Orders in Davie
Sightline Windows & Doors has documented more than 18,000 openings since 2012 – every one with a written price before work started and a photo record when it finished. Sonia Raman built the company’s process around the idea that the measurement and the quote are the same document, because that’s the only way a custom order stays honest from survey to final inspection.
For Davie homeowners, that structure matters more than it might in a less regulated market. HVHZ compliance, Town of Davie permitting, and the specific opening challenges in pre-2000 construction all create opportunities for costs to migrate from the quote to the invoice. Sightline’s written process, documented under the Haven Standard, is specifically designed to prevent that migration. The price on the survey document is the price on the invoice. Haven Clause 1 is not a promotional promise; it’s the founding principle the company has operated under since it opened.
If you’re planning a custom window or door order anywhere in Davie – from the newer planned developments near Interstate 595 to the older ranch-block neighborhoods along Stirling Road – we can schedule a measured survey and deliver a written price within a few days of your call. There is no charge for the survey, and no obligation to proceed. The document you receive after the survey is yours regardless.
To learn more about what we install and order across the full range of window and door types, visit our home page or go directly to the Custom Window & Door Order in Davie service page for the complete product and process detail.
Get a Written Price on Your Davie Custom Order
Call (754) 254-8492 to schedule your measured survey. A live person answers every call. The survey is free, the written price is yours to keep, and nothing about that price changes between survey day and installation day. That’s the Haven Standard, applied to every custom window and door order we complete in Davie.
Pricing reflects the Davie market as of 2026. Sightline Windows & Doors Davie offers free estimates – call (754) 254-8492.
Written by Sonia Raman, Owner at Sightline Windows & Doors, serving Davie since 2012.
What Our Customers Say
"The road noise in the front bedroom is genuinely gone. They recommended the laminated glass and explained why, with figures."
- Delia F."They photographed the rotten sill they found under the old frame before replacing it, and the extra cost was agreed in writing before they carried on."
- Rosalind C."The survey measurements and the quote were the same piece of paper. Nothing changed on install day, which is not what happened with the two other companies we had out."
- Annette R.