Mr-Glass Door Installation Nationwide | Sightline Windows & Doors Davie

Mr-Glass Door Installation: The Davie Owner’s Guide

Mr-Glass door installation in Davie typically runs $1,200-$2,800 for a standard single entry unit, depending on whether the opening needs a retrofit into existing framing or a full-frame replacement. We stock Mr-Glass hardware and installation kits on our trucks, and most replacements in Davie are completed in a single day once the measured survey is approved. Homeowners usually discover a problem when the door sticks in humid weather, the multipoint lock won’t engage, or they notice daylight around the frame where the seal has compressed after years of Florida heat cycling.

Call (754) 254-8492

Which Mr-Glass Models This Applies To

Mr-Glass produces several door series, and the installation approach differs meaningfully between them. The MG-Impact line, their hurricane-rated fiberglass entry door, uses a 6-9/16″ jamb depth with integrated composite sill and requires impact-rated fasteners at 8″ on-center through the hinge side. The MG-Select steel entry series uses a 4-9/16″ jamb and a standard aluminum sill pan. The MG-Slide patio door system, popular in Davie’s 1990s-era Pine Island Ridge builds, carries a heavier dead-load requirement and needs shimming at the head every 24″ to prevent sag on the 8-foot widths common in those homes.

To identify your series, check the hinge-side label for a stamped MG code, or measure the jamb depth with the door open. The OEM installation kit from Mr-Glass includes pre-cut shims and proprietary fasteners, but we also carry third-party equivalents that meet Miami-Dade HVHZ requirements at lower cost. The catch: MG-Impact doors installed within five miles of the coast, including parts of Davie near the New River basin, require 316 stainless fasteners rather than the standard zinc-plated hardware in the base kit. We stock both. Sightline Windows & Doors Davie is an independent service provider, not affiliated with Mr-Glass.

Signs Your Mr-Glass Door Installation Is Failing

• The door drags or binds at the top corner. This usually means the frame has racked during a seasonal humidity swing. In Davie, where summer interior humidity can hit 65% and winter drops to 40%, the jamb legs move at different rates if the original installer didn’t leave proper expansion clearance at the head.
• Water stains appear at the base of the interior trim. The sill pan is either cracked, improperly flashed, or the end dams were sealed with caulk instead of backer rod and sealant. Mr-Glass sills are composite and don’t rot, but the subfloor beneath them does.
• The multipoint lock won’t throw or retract smoothly. The mechanism is fine; the frame has settled and the keeps no longer align. This is common in MG-Slide units where the head wasn’t properly shimmed during original installation.
• You feel drafts even with the door closed and locked. The compression seal has taken a set after years of UV exposure. Mr-Glass uses a dual-fin weatherstrip that works well for about 8-10 years in South Florida before the EPDM hardens.
• The door closes but won’t latch without lifting the handle. The hinges have elongated their screw holes in the jamb, or the hinge screws were too short for the door weight. MG-Impact doors weigh 140-180 pounds; standard 1″ screws pull out.

Before

After

Replacement Cost & What’s Included

These prices include the measured survey you keep, the written scope that cannot change without a change order, removal and disposal, new fasteners and sealants, and the documented photo record. What drives the range: jamb depth, whether the existing frame is square within 1/8″ over its height, and whether we find subfloor damage once the old unit is out. We pull permits when required by Davie building code, which is any impact-rated replacement in a designated wind-borne debris region. Every installation carries our 365-Day Done Right Promise under the Haven Standard.

DIY or Call Us?

There is nothing dangerous about hanging a door, but there is plenty that goes wrong. A homeowner can safely check the hinge screw length with the door open, verify whether the sill pan end dams are sealed, and photograph the label for us to review. What goes wrong: the frame goes in out-of-square, the sill pan pitches toward the house instead of away, or the fastener pattern misses the king stud and splits the jack stud. In Davie, where many homes sit on fill with seasonal settling, a door that looks plumb today may rack within six months if the shimming is wrong.

We have re-hung doors that homeowners started on Saturday and called about Sunday evening. The cost to fix a DIY attempt usually exceeds the original quote because we have to remove fasteners that were driven into wrong locations. Call (754) 254-8492 and we will schedule a measured survey. The written price is yours to keep whether you hire us or not.

FAQs